HEX performance analysis

Enter the heat-exchanger conditions once. Compare exergy destruction, reversible reference work and heat-recovery targets from the same stream data.

Start with the 100 kW counterflow example or transfer an operating point from Fzz.

Shared HEX configuration

All three analyses use these stream inputs. Select the basis of the entered capacities. Switching basis retains the numbers and changes their units. Per-cycle values require the heat capacity of the mass passing per reference cycle.

Hot stream
Cold stream

Exergy Lost Work

The reference environment sets the conversion from entropy generation to exergy destruction.

Delivered heat
100 kW
Entropy generation
0.0338 kW/K
Lost work at T₀
10.09 kWSame stream states · environment at 298.15 K
Lost work per unit of delivered heat
0.101 kW/kW
Exergy efficiency for heating
50.5%
Actual shaft work
0 kW
Energy and exergy balances

Hot-stream heat release 100 kW. Cold-stream heat gain 100 kW. Energy residual 0 kW.

Terminal temperature differences 30 K and 55 K. Hot-stream exergy consumption 20.37523 kW. Cold-stream exergy gain 10.28855 kW.

The energy check allows a relative numerical mismatch of 10⁻⁷. Use a balanced point for this adiabatic model.

Reversible work under each constraint

The first reference gives lost work for the same stream states. The other two change a process outlet and therefore the duty on that side.

  • Fixed stream states + environment10.09 kW
  • Fixed source cooling11.62 kW
  • Fixed heat delivery11.74 kW
Reversible reference balances
Fixed conditionHot outlet (K)Cold outlet (K)Source heat (kW)Delivered heat (kW)Ambient heat (kW)Entropy residual (kW/K)
Both outlet states35034510010010.086680
Hot outlet350342.0943910088.3775601.665e-16
Cold outlet344.12938345111.741231000-1.110e-16

Exchanger trajectories

Both diagrams describe the same exchanger. The heat and area coordinates start at the cold inlet. The area calculation uses dQ̇ = U ΔT dA at the U entered below.

T–Q · Actual exchanger

  • Hot stream
  • Cold stream
315.20337.62536050382.475404.8100Transferred heat (kW)Temperature (K)
The hot stream flows from right to left. The cold stream flows from left to right.

T–A · Actual exchanger

  • Hot stream
  • Cold stream
315.20337.63.0313606.061382.49.092404.812.12Cumulative area (m²)Temperature (K)
Required area at the specified constant U is 12.12 m².

How to read the results

Actual operating point and exergy destruction

The calculation assumes an externally adiabatic exchanger with positive absolute temperatures and two constant-capacity streams. It models the thermal contribution to entropy generation. An assessment including pressure losses, heat leaks, mixing or auxiliaries needs the corresponding full balances.

The hot and cold streams exchange positive entropy magnitudes. The equations use rates for steady operation or totals per reference cycle, according to the selected basis.

JH=CHln(TH,inTH,out)
JL=CLln(TL,outTL,in)

The entropy generation equals the difference between these magnitudes. Equivalently, integrate the local entropy generation along the paired heat-transfer trajectory.

Sgen=JL−JH=∫0Q(1TL−1TH)dq

At the chosen reference-environment temperature, exergy destruction gives the lost work.

ED=T0Sgen

For a heating service entirely at or above T0, the exergy efficiency is the cold stream’s exergy gain divided by the hot stream’s exergy consumption.

ηex=ΔEL,gainΔEH,consumed
Reversible references and what each one holds fixed

The three references below retain both inlet temperatures and stream capacities. With two reversible thermal contacts, the Clausius equality determines one free outlet. The energy balance then gives the reference work.

JH=JL,Wrev=QH−QL
  • Fixed source cooling. Keep the hot outlet and solve for the cold outlet.
    TL,out=TL,inexp(JHCL)
  • Fixed heat delivery. Keep the cold outlet and solve for the hot outlet.
    TH,out=TH,inexp(−JLCH)
  • Fixed stream states and ambient contact. Keep both outlets and add reversible heat input from the reference environment.
    Q0=T0Sgen,Wrev=QH+Q0−QL

    With equal source and delivered duties, Wrev=Q0. This gives the lost work of the actual zero-shaft-work case.

The two-contact references pair equal increments of entropy transfer. They require a nonnegative local temperature difference for heat-engine operation. Each reference describes a reversible limit under its stated constraints.

Pinch targets and the area diagram

Pinch Analysis shifts the hot and cold temperatures by half the chosen minimum approach. It then cascades net heat across the shifted intervals. The utility targets and maximum heat recovery apply to steady sensible streams with constant capacities and unrestricted matching.

TH∗=TH−ΔTmin2,TL∗=TL+ΔTmin2

The T–A diagram uses the actual exchanger’s stream pairing and a constant overall heat-transfer coefficient U.

dA=dQ˙UΔT

For these linear temperature trajectories at positive duty and finite U, the calculated area grows without bound as a terminal temperature difference approaches zero. Sizing individual exchangers from a composite curve requires a defined network and local stream matches.

See Linnhoff and Hindmarsh, The pinch design method for heat exchanger networks.

Relation to the CarnotX reversibility studies

The two companion studies show how an idealised non-isothermal Brayton cycle can move between zero net work and a reversible endpoint by changing hot-side matching, cold-side matching or internal component performance. Both heat duties determine net work. Holding both fixed also fixes net work, even if the temperature trajectories change.

The performance tool applies this distinction to an exchanger with fixed stream capacities and explicit service constraints. The Reversible Cycle Benchmark also has separate exploratory routes that vary only temperatures or heat quantities.

Sources and model scope

The lost-work examples draw on technical reports and research documents prepared by the CarnotX research team.

For the distinction between reference-environment exergy destruction and work loss under other system constraints, see Tu and Chen, Rethinking Loss of Available Work and Gouy–Stodola Theorem.