Adjust the thermal trajectories
Change the interacting temperature profiles through stream conditions, material selection or process design. Assess the resulting local gaps, heat duty and entropy generation under the declared constraints.
Thermal processes · Technical article
Relating temperature trajectories, heat-transfer conductance and irreversibility in non-isothermal heat exchange.
How do paired temperature trajectories, conductance and exchanger area determine heat-transfer irreversibility? For a steady counterflow exchanger with two separated streams, this article derives the heat and entropy balances and shows the same calculated process in T–Q and T–A coordinates. The example demonstrates why the geometric gap between curves is not itself exergy destruction. It assumes constant properties, no external heat loss and no pressure loss; applying the result to a complete cycle requires an additional model and declared comparison conditions.
The starting boundary encloses both streams and their separating heat-transfer surface. The exchanger is steady, externally adiabatic and produces no shaft work. Changes in kinetic and potential energy are neglected. Under these assumptions, heat released by one stream equals heat received by the other. The analysis addresses thermal irreversibility; pressure loss would add another contribution.
Thermal Matching means adjusting the temperature–heat-transfer trajectories of interacting media in shape, temperature level or heat-duty distribution. Possible variables include flow rate, working-medium properties, operating pressure, staging and cycle architecture. A proposed adjustment must satisfy energy balances, local heat-transfer direction and the available conductance.
Here Th and Tc denote the local hot- and cold-stream temperatures in kelvin, and ΔT = Th − Tc > 0. The positive increment dQ̇ is heat transferred from hot to cold, measured in watts. The cumulative heat-rate coordinate Q̇cum is not time, shaft work or physical exchanger length. In a cycle calculation, Q per cycle or q per unit mass may be used instead; the chosen basis must remain consistent.
Change the interacting temperature profiles through stream conditions, material selection or process design. Assess the resulting local gaps, heat duty and entropy generation under the declared constraints.
Increase conductance through heat-transfer coefficients, conductivity, area or geometry. For a specified duty and a compatible profile family, greater conductance can support smaller driving temperature differences.
These interventions are coupled. Changing flow rate can alter both the temperature glide and U; changing refrigerant can alter phase behaviour, pressure loss and compressor work. An increase in UA cannot independently prescribe an arbitrary profile. Likewise, closer-looking curves do not establish a feasible heat exchanger.
Let A be the physical heat-transfer area in m² and U the overall coefficient in W/(m² K), on the same area basis. For the local heat-transfer model:
With constant U, the required conductance follows from the paired profiles: UA = ∫ dQ̇/ΔT. In conventional counterflow analysis this is equivalent to Q̇ = UA ΔTlm where the logarithmic-mean temperature difference is applicable. The local relation and conductance definition follow standard heat-exchanger theory [1].
Neglecting pressure losses and other dissipative effects, the entropy generation rate of the complete exchanger is:
Ṡgen has units W/K. For a reference environment at T₀ > 0 K, exergy destruction is ĖD = T₀ Ṡgen, in watts. This measures destroyed work potential at that reference environment. It is not an energy-balance loss: the heat duty remains conserved across the externally adiabatic exchanger. Entropy analysis complements heat-transfer analysis [2].
At finite conductance, nonzero heat transfer requires a driving temperature difference. Exact local temperature coincidence is a reversible limiting case requiring unbounded conductance for a finite duty within this model.
A T–Q diagram allocates horizontal width according to heat transferred. A T–A diagram allocates width according to physical area. Their local temperature differences describe the same paired stream states, but are weighted differently. With constant U:
At fixed heat duty and fixed constant U, this integral is unchanged between configurations, even if its distribution changes. Its unit K·m² is different from the physical area unit m². With spatially varying U, the general relation is Q̇ = ∫ U(A) ΔT(A) dA; the unweighted integral need not be invariant.
Substitution of dQ̇ = U ΔT dA gives ∫ ΔT dQ̇ = U ∫ (ΔT)² dA. Thus identical ∫ ΔT dA does not imply identical ∫ ΔT dQ̇. At fixed Q̇, constant U and total A, constant ΔT minimizes this squared-gap integral among admissible profiles. This follows directly from the nonnegative variance of ΔT.
Entropy generation has the additional absolute-temperature weighting: Ṡgen = ∫ U(ΔT)²/(ThTc) dA. Neither geometric gap integral alone is an exergy measure, and constant ΔT is not a universal minimum-entropy-generation condition. Any optimum depends on the allowed profiles and constraints.
Consider Q̇ = 10 kW with constant U = 200 W/(m² K). The hot stream cools from 450 to 350 K, with heat-capacity rate Ch = 100 W/K. The cold stream warms from 300 to 420 K, with Cc = 83.333… W/K. These are illustrative constant-property streams, not a specified fluid or measured apparatus.
Starting at the cold inlet / hot outlet end, let q be the numerical cumulative heat rate in kW. Then Th = 350 + 10q and Tc = 300 + 12q, with temperatures in kelvin and 0 ≤ q ≤ 10. The local gap falls from 50 to 30 K. The area mapping is q(A) = 25[1 − exp(−0.4A)], where the numerical area A is in m².
| Quantity | Result |
|---|---|
| Heat-transfer rate | 10.000 kW |
| Logarithmic-mean ΔT | 39.152 K |
| Required UA | 255.413 W/K |
| Required physical area | 1.27706 m² |
| T–A gap integral ∫ ΔT dA | 50.000 K·m² |
| T–Q gap integral ∫ ΔT dQ̇ | 400.000 K·kW |
| Entropy generation rate | 2.90791 W/K |
| Exergy destruction at T₀ = 298.15 K | 0.86699 kW |
Energy balance: 100 × (450 − 350) = (10000/120) × (420 − 300) = 10000 W. Conductance: UA = [10000/(50 − 30)] ln(50/30) = 255.413 W/K. Divide by U to obtain A.
The independent stream-entropy balance gives Ṡgen = 100 ln(350/450) + (10000/120) ln(420/300) = 2.90791 W/K, equal to integration of the paired local reciprocal-temperature difference.
Both diagrams show this single exchanger, not a before/after optimization. No percentage saving or optimal profile is inferred. The 0.86699 kW exergy destruction is a reference-environment quantity; recovering that amount as practical shaft work would require a separately specified reversible arrangement.
A useful comparison declares what stays fixed: heat duty, useful heating or cooling service, inlet states, flow rates, area, U, pressure limits or working-fluid cycle. Not all of these can generally be fixed independently. Solving a different set of constraints gives a different engineering question.
For heat engines, heat pumps and refrigeration, distinguish the working medium from the external heat-source and heat-sink streams. Changing only an external profile while holding both working-fluid heat duties fixed leaves net cycle work unchanged by the First Law. A change in efficiency or COP requires the corresponding cycle and useful-output calculation. Zeotropic refrigerants, transcritical gas cooling and staging offer profile variables, but no benefit is universal.
Cyclically loaded solid media can exchange heat with external surroundings as their temperature changes during deformation. Applying the same balance logic requires a time-resolved thermal and mechanical model. The steady counterflow area coordinate used here is not automatically a spatial description of such a solid cycle.
In an open combustor, chemical energy release, transport and mixing occur within a reacting stream. A separated-stream T–Q comparison can be a proposed analogy; it does not replace a reacting-flow model or establish fuel savings.
The Clausius reversible-cycle equality and exergy balances are established thermodynamic principles. CarnotX’s Parent Reversible Cycle Benchmark Framework organizes their use with energy, material and process relations and admissibility conditions. It provides a proposed operational method for comparing declared references. The exchanger calculation above is an analytical example, not independent experimental validation of the framework or an optimized machine.
The following links leave this article and open the corresponding tool or supporting article. Check the model description and fixed/free inputs in each module.
The coordinate identities and numerical example are derived here from the stated local heat-transfer law and energy/entropy balances. The example has no experimental data and assumes constant properties. Source access checked 22 November 2026.